Chemical Engineering December 2014 - 25

Source: Henkel
Source: Cortec
Newsfront
crosslinked in a single oven. "
" This process is unique to our coatings, "
says Mike Berger, business
development manager with Henkel.
" Many other coatings require users
to wholly cure the primer before the
top coat can be applied, which requires
two ovens and much longer
durations of time at higher temperatures.
In new applications, end users
can employ a shorter oven, which
results in lower equipment costs. In
existing lines, they can turn down
the oven temperature and reduce
the time and save energy. "
The Co-Cure process can be used
with Bonderite M-PP 930 Autodeposition
Coating. The coating delivers
enhanced corrosion performance in
applications such as vehicle frames
and chassis components, construction
equipment and appliances (Figure
3). The environmentally sustainable
coating contains no toxic heavy
metals and is very low in VOCs.
In addition to its environmentally
friendly profile and application
Figure 3. Bonderite M-PP 930 Autodeposition
Coating from Henkel delivers
enhanced corrosion performance in applications
such as vehicle frames and
chassis components
process, the coating was developed
for use on difficult-to-coat reactive
substrates where traditional protectants
could not provide a uniform
coating, which often resulted
in exposure to corrosion through
microscopic pinholes. Bonderite
M-PP 930C addresses issues applicators
face when coating cast substrate
by eliminating surface voids
and outgassing, which contribute to
improved corrosion properties. Because
Bonderite M-PP 930 provides
uniform coverage with lower maintenance
requirements - there is no
Figure 4. Cortec's Ecosonic Conformal
Coating powered by Nano-VpCI for use as a
circuit-board conformal coating combines
moisture-intrusion prevention and corrosion
resistance with the company's Vapor-phase
Corrosion Inhibitor (VpCI) technology
ultrafiltration, no rectifiers, no electrodes
and fewer stages - the coating
is expected to last 5 to 10 years
under extreme corrosion conditions,
says Henkel's Abu-Shanab. This
combination of the shorter cure time
and the reduction in maintenance
results in lower labor costs, says
Berger, which is another demand on
today's protective coatings.
Cortec Corp. (St. Paul, Minn.;
www.corteccvci.com) also saw an
opportunity to improve several proKNOWLEDGE
& EXPERIENCE
KNOWLEDGE & EXPERIENCE
Downtime is critical for turnarounds.
The ONE SOURCE SOLUTIONSM
Approach
On-time design and supply of equipment as well as precise installation
result in less downtime. The direct access between the supplier and installer in
the ONE SOURCE SOLUTIONSM
approach delivers around-the-clock problem
solving and seamless communication. The combination of Koch-Glitsch
engineering and Koch Specialty Plant Services field personnel provides the
knowledge and experience to optimize the safety, accuracy and efficiency of
each installation.
YOU CAN RELY ON US.™
YOU CAN RELY ON US.™
United States (316) 828-5110 | Canada (905) 852-3381 | Italy +39 039 6386010 | Singapore +65-6831-6500
For a complete list of our offices, visit our Web site.
www.koch-glitsch.com
" K " KOCH-GLITSCH is a trademark of Koch-Glitsch, LP and is registered in the USA and various other countries.
YOU CAN RELY ON US is a trademark of Koch-Glitsch, LP. ONE SOURCE SOLUTION is a service mark of Koch Specialty Plant Services, Inc.
Circle 12 on p. 60 or go to adlinks.che.com/50983-12
ChemiCal engineering wwww.Chemengonline.Comm DeCemBer 2014 25

http://www.corteccvci.com http://www.koch-glitsch.com http://adlinks.che.com/50983-12

Chemical Engineering December 2014

Table of Contents for the Digital Edition of Chemical Engineering December 2014