Geosynthetics December 2019/January 2020 - 47

GEOTEXTILES
M288 Transportation-Related Applications

Wide Width Tensile/Elongation
ASTM D 4595 kN/m (lb/in)/%

Grab Tensile/Elongation
ASTM D 4632 kN (lb)/%

M288 Survivability Class

M288 Applications [4]

Creep Limited Strength-MD
ASTM D 5262 [6] kN/m (lb/ft)

LTDS GRI GT7-MD (in sand) [7]
kN/m (lb/ft)

Other Manufacturer's
Suggested Applications [8]

NP

NP

N/A

N/A

N/A

N/A

N/A

N/A

F, D, E

1.82 (410)

0.267 (60)

0.711
(160)/50

2

SP, D

N/A

N/A

N/A

N/A

N/A

N/A

S/F, F, E

1.35/3657 (90), FH

2.33 (525)

0.356 (80)

0.911
(205)/50

1

SP, D,
ST, E

N/A

N/A

N/A

N/A

N/A

NA

S/F, F, D, E

0.15 (100)

1.1/3251 (80), FH

2.89 (650)

0.444 (100)

1.11
(250)/50

1

SP, D,
ST, E

N/A

N/A

N/A

N/A

N/A

N/A

S/F, F, D, E

N/A

0.15 (100)

0.7/2035 (50), FH

4.56
(1025)

0.644 (145)

1.69
(380)/50

1

SP, D,
ST, E

N/A

N/A

N/A

N/A

N/A

N/A

S/F, F, D, E

NP

1

0.43 (40)

0.05/200 (5), FH

3.11 (700)

0.330 (75)

0.9 (200)/15

3

SP, ST

N/A

N/A

N/A

N/A

N/A

N/A

LM315 NT
(W-SP/PP)

NP

1

0.43 (40)

0.05/163 (4), FH

4.0 (900)

0.533 (75)

1.4 (315)/15

1, 2, 3

SP, ST

N/A

N/A

N/A

N/A

N/A

N/A

LM2199 FW

NP

4

0.212 (70)

0.28/733 (18)

4.2 (950)

0.445 x 0.267
(100 x 60)

1.6 x 1.1
(370 x 250)
15 x 15

2, 3

D, E

N/A

N/A

N/A

N/A

N/A

N

S/F Bulk Head

LM270 HP

NP

N/A

0.60 (30)

0.7/2037 (50)

4.5 (1000)

N/A

1.3 x 1.2
(295 x 250)

17.7
(1212)

19.8
(1356)

38.5
(2640)

35.9
(2460)

N/A

LM570 HP

NP

N/A

0.60 (30)

0.40/1222 (30)

8.9 (2000)

N/A

2.2 x 2.1
(500 x 475)
11 x 4

1A

Enhanced
Stabilization

35.0
(2400)

39.4
(2700)

70.0
(4800)

70.0
(4800)

N/A

Mass Per Unit Area
ASTM D 5261 g/m2 (oz/yd2)

Permittivity
ASTM D 4491 sec-1
Flow Rate (FH or CH) [3]
l/min/m2 (gal/min/ft2)

.400 (90)/50

Apparent Opening Size
ASTM D 4751 mm
(U.S. sieve)

0.178 (40)

Percent Open Area
CWO-22125 %

1.11 (250)

Product Name (Structure [1]/
Polymer Type [2])

Trapezoid Tearing Strength
ASTM D 4533 kN (lb)

Physical Properties

Puncture ASTM D 6241
kN (lb)

Filtration/Hydraulic Properties

Reinforcement Applications

Strength @ 5%
Strain [5]

Ultimate
Strength %
(Tult) [5]

MD

XD

MD

XD

L & M Supply l www.landmsupplyco.com
LM400 NT
(NW-P/PP)

NP

N/A

.212 (70)

2.1/6095 (150), FH

LM600 NT
(NW-P/PP)

NP

N/A

.212 (70)

1.5/4880 (110), FH

LM800 NT
(NW-P/PP)

NP

N/A

0.18 (80)

LM1000 NT
(NW-P/PP)

NP

N/A

LM1600 NT
(NW-P/PP)

NP

LM200 NT
(W-SP/PP)

Maccaferri Inc. l www.maccaferri.com/us
MacTex N21.1
(NW-P/PP)

NP

NP

0.212 (70)

1.7 / 4885 (135)

1.51 (340)

0.22 (50)

0.533 (120)
/ 50

>>3

ST, SP, D,
F, E

NA

NA

NA

NA

NA

NA

NA

MacTex N47.1
(NW-P/PP)

NP

NP

0.18 (80)

1.4 / 3657 (95)

2.38 (535)

0.378 (85)

0.911 (205)
/ 50

>>1

ST, SP, D,
F, E

NA

NA

NA

NA

NA

NA

NA

MacTex W1 250
(W-SF/PP)

NP

NP

0.425 (40)

0.05 / 163 (4)

4.45 (700)

0.444 (100)

1.11 (250)
/ 15

>>2

ST, SP, D,
F, E

NA

NA

NA

NA

NA

NA

NA

[1]	
	
	
[2]	
[3]	
	
[4]	
	
	
	
[5]	

NW	
W	
K	
PP	
FH	
CH	
SP	
ST	
F	
A/O	
MD	

= Non woven, -P = needlepunched, -h = calendered
= Woven, -SF = slit film	
t	
= thermally bonded
= Knitted	
O/C	 = Other/combination
= Polypropylene, PET = Polyester, * = average
= Test is run by the falling head method
= Test is run by the constant head method
= Separation	
S/F	 = Silt Fence
= Stabilization	
D 	 = Drainage
= Filtration	
E	
= Erosion Control
= Asphalt overlay
= Machine direction	
XD = Cross-machine direction

[6]	 For a minimum of 10,000 hours, extrapolated to
	 a 75 year time period
Tult
[7]	 LTDS =	
	
RFCR x RFID x RFD
	RFCR = Reduction factor for creep
	RFID = Reduction factor for installation damage
	RFD = Reduction factor for durability
NOTE: this equation does not include other reduction factors which may apply to
design. Reduction factors are site specific and should be reviewed on a per project
basis. Contact the manufacturer for recommendations.

[8]	 R	 = Reinforcement	
P	 = Protection
	 SP	 = Separation	
S/F	 = Silt Fence
	 ST	 = Stabilization	
D	 = Drainage
	 F	 = Filtration	
E	 = Erosion Control
	 RC	 = Reinforcement Composite
	 A/O	 = Asphalt overlay
NP	 = Not provided by manufacturer
NA	 = Not applicable, per manufacturer
Companies were requested to provide minimum average
roll values (MARV). All claims are the responsibility of
the manufacturer.

« Geosynthetics recommends you contact the manufacturers before making any specifying/purchasing decisions »
www.GeosyntheticsMagazine.com

47
http://www.landmsupplyco.com http://www.maccaferri.com/us http://www.GeosyntheticsMagazine.com
Geosynthetics December 2019/January 2020

Table of Contents for the Digital Edition of Geosynthetics December 2019/January 2020
