WIREMOLD / PERIMETER SYSTEMS 3000 SERIES® RACEWAY 3000 Series Raceway Ordering Information (continued) Bump-Up Extron® MAAP Plate 1 13/32 " (36mm) 7 15/16 " (185mm) 2 13/16 " (72mm) PART NUMBERS: V3046U (Ivory) G3046U (Gray) Device plate for use with four Extron® Electronics MAAP single space modules. Bump-Up Extron® 1 13/32 " (36mm) 2 13/16 " (72mm) 7 15/16 " (185mm) AAP Plate PART NUMBERS: V3046V (Ivory) G3046V (Gray) Device plate for use with two Extron® Electronics AAP single space modules. Bump-Up Ortronics® 1 13/32 " (36mm) 7 15/16 " (185mm) 2 13/16 " (72mm) Series II Plate PART NUMBERS: V3046S (Ivory) G3046S (Gray) Device plate for use with three Ortronics® Series II modules. 6 TracJacks, or Wiremold CM Series inserts. 2 13/16 " (71mm) DRP20A-V Colormatch Ivory Duplex Receptacle & Plate Specification grade rated 20A 125V NEMA 5-20R receptacle with color matched nylon faceplate. Receptacle has nylon face and thermoplastic base. One-piece brass triple-wipe line contacts and double-wipe ground contacts. Locked in wrap-around steel yoke. Break off tab for two circuit wiring. 2.7 " W x 4.5 " H (69mm x 114mm). Verified under Fed. Spec. #WC596F. Colormatch Gray or Ivory Receptacle PART NUMBERS: DR20A-V (Ivory), DR20A-G (Gray) Specification grade rated 20A 125V NEMA 5-20R receptacle. Receptacle has nylon face and thermoplastic base. One-piece brass triple-wipe line contacts and double-wipe ground contacts. Locked in wrap-around steel yoke. Break off tab for two circuit wiring. 2.7 " W x 4.5 " H (69mm x 114mm). Verified under Fed. Spec. #WC596F. 3000 Series Raceway Installation Details 1. Determine the method of feeding raceway using an entrance end fitting or through 1/2 " or 3/4 " trade size KO in raceway base (shown). 3000 Series Raceway Base Conduit Connector 2. To mount 3000 Base on surface: Remove mounting screw KOs (approx. 9 3/8 " (238mm) O.C. along base) as required. Mount base with No. 8 flathead fasteners. Mounting Screw KOs Feed KOs 4. To install devices: Install device bracket in 3000 Base. Wire device and assemble on bracket. Install cover over 3000 Base and device (if device has plaster ears, break off before mounting on device bracket). 3000 Series Raceway Base 3. For coupling lengths of 3000B, insert either the G3001 or G3001A (shown) into one base section centered on joint. Slide other length of base onto coupling. Tighten locking screws. 494 WWW.LEGRAND.US/WIREMOLD 9 3/8 " (238mm) Approx. Base Sections 5. Cut sections of 3000 Cover to fit between device plates. Snap cover sections in place along entire run as shown. Engage One Side Of Cover On Base 3000 Base Break Off G3082 Conduit Connector 2 11/16 " (68mm) Connects end of 3000 Series Raceway to 1 1/2 " trade size conduit or armored cable. Device Bracket Cover Device Snap Cover Onto Base 3001A STEEL RACEWAYhttp://WWW.LEGRAND.US/WIREMOLD