Cablofil Cable Management Catalog 2018 - D.40

FASTENERS

ROD STIFFENER CLIPS
Rod stiffener clips attach strut or pipe to hanger rods in order to prevent buckling of the rods, when the rods
themselves are not strong enough to resist upward vertical forces, and when compression resistance to upward
vertical forces is required.
QUICK CLIP™ FOR STRUT/CHANNEL

RS1" FOR PIPE

The Quick Clip™ is the fastest, easiest-to-use rod
stiffener on the market. For use with 1-5/8" x 1-5/8"
12-gage strut and 3/8" or 1/2" hanger rod, the unique
BRACE ANCHORAGE TO
design offers effortless one-handed installation in
BUILDING STRUCTURE
USING STAKE EYE
lessTRAY
than
5 seconds
- with no tools needed!
CABLE
SUPPORT
ROD
OR URC CLIP (TYP.)
FOR CENTER-HUNG TYPE
TRAY SUPPORTS (TYP.)
(ONE ROD PER SUPPORT)

(SEE DETAILS AT
WWW.LEGRAND.COM/CABLOFIL)

EASY AS 1-2-3!

CABLE TRAY
SIDE RAIL
STAKE EYE
END OF SEISMIC
WIRE
ROPE/CABLE™
(TYP.)
THREADED SUPPORT

1. With the rod in the rear, right corner, insert
the Quick Clip™ into the strut.

The RS1 rod stiffener is
used with 1" Schedule 40 or
2. Rotate the Quick
Clip™
clockwise 90 degrees.
ROD
TO STRUCTURE
CLIP #0602
10 steel pipe and
6" MAXIMUM Schedule
45°
1 / " xto
1 /lock
" x 12in
GA.
STEEL STRUT
3. (TYP.)
Push
place.
3/8",
1/2"
and 5/8" hanger rod.
FOR ROD STIFFENER*
BRACE CONNECTION TO
STRUT
CABLE TRAY SUPPORT
It snaps over the pipe and rod,
USING URC CLIP (TYP.)
1" SCH, SCH 40 or RIGID STEEL CONDUIT MAY
(SEE
SEEDETAILS
TABLEATFORand connects easily with a
BE SUBSTITUTED FOR 1 / " STEEL STRUT
WWW.LEGRAND.COM/CABLOFIL)
MAX. SPACING
SEISMIC WIRE ROPE/CABLE™
SUPPORT
ASSEMBLY (TYP.)
provided
bolt and lock nut.
ROD STIFFENER CLIPS
ROD
5

8

5

™

8

5

8

PART #0602 (UP TO 5/8" RODS)
OR #0603 (3/4" & ABOVE RODS)

RS1
SEE TABLE FOR
MAX. SPACING

CABLE TRAY SUPPORT MEMBER
(TYPICALLY 15/8" x 12 GA. STEEL STRUT)

PW-QC3/8

PIPE
6" MAXIMUM
CABLE
TRAY

PW-QC1/2

CABLE TRAY SUPPORT ROD
FOR TRAPEZE TYPE CABLE
TRAY SUPPORTS (TYP.)
(2 RODS PER SUPPORT)

SUPPORT
ROD

SUPPORT MEMBER
(TYP.)

SUPPORT ROD STIFFENER DETAILS AND REQUIREMENTS (AT SWAY BRACE LOCATIONS ONLY)
CABLE TRAY SUPPORT ROD (TYP.) FOR
TRAPEZE TYPE CABLE TRAY SUPPORTS
(SEE ROD STIFFENER REQUIREMENTS
AT WWW.LEGRAND.COM/CABLOFIL)

BRACE ANCHORAGE TO
BUILDING STRUCTURE
USING STAKE EYE (SHOWN)
OR URC CLIP (TYP.)
(SEE DETAILS AT
WWW.LEGRAND.COM/CABLOFIL)

CABLE TRAY SUPPORT ROD (TYP.)
FOR CENTER-HUNG TYPE CABLE TRAY
SUPPORTS (SEE ROD STIFFENER
REQUIREMENTS AT
WWW.LEGRAND.COM/CABLOFIL)

!"

!"
/2" INSIDE DIA.
SCH. 40 PIPE
(CENTER-HUNG
SUPPORTS)

SEISMIC BRACING

1

TIGHTEN CABLES
ONLY TO REMOVE
EXCESSIVE SLACK

CABLE TRAY

OVAL SLEEVE

TWO WIRE ROPE/CABLE
ASSEMBLIES (ASSEMBLY
IN FOREGROUND SHOWN)
CABLE TRAY SUPPORT MEMBER

45°
BRACE
ANGLE
(TYP.)

CABLE LOOP
15/8" SQUARE WASHERS
AND HEX NUTS, TOP
AND BOTTOM (TYP.)

BRACE CONNECTION TO
CABLE TRAY SUPPORT
USING URC CLIP (TYP.)
(SEE DETAILS AT
WWW.LEGRAND.COM/CABLOFIL)

For multi-tier support systems, the steel strut rod stiffener shall be installed such that it be secured to the side of the bottom support
member, in contact with the structure, and held in position by securing to the side of one other horizontal support member, using the rod
D.40 stiffener clips shown above.
WWW.LEGRAND.US/CABLOFIL
http://WWW.LEGRAND.COM/CABLOFIL http://WWW.LEGRAND.COM/CABLOFIL http://WWW.LEGRAND.COM/CABLOFIL http://WWW.LEGRAND.COM/CABLOFIL http://WWW.LEGRAND.US/CABLOFIL
Cablofil Cable Management Catalog 2018

Table of Contents for the Digital Edition of Cablofil Cable Management Catalog 2018
