Waytek Catalog 225 - 109

Battery Management
Wire & Cable
® ®

LOW VOLTAGE DISCONNECTS
• Automatically disconnects non-critical
Low Battery Alarm
Stock No. 80028

Low Battery Switch
Stock No. 80029

SAE J1455

SAE J1113

185°F (85°C) -40°F (-40°C) (at 20-amp load)
Stock No.
80028 80029

Description
Low Battery Alarm Low Battery Switch

Current
NA 20

1001 130512

Adjustable 11.1V to 12.5V 12V

Low Voltage Disconnect Switch with Shut-Off Timer

Cole Hersee Flexmods™

• Continuously monitors voltage level of a 12 volt
power input

• If voltage >13.25 - power switch turns on • If voltage drops < 12.8 - time delay is started • If voltage remains < 12.8 until the timer expires

Application

Smart Battery Isolator Controller

185°F (85°C) -40°F (-40°C )

• Monitors two battery banks and controls one or more relays to make sure
Electronic Voltage Sensing Relay & Timer

starting power is protected by isolating the starting and auxiliary battery banks
Battery Management

• Monitors both battery voltage and ignition status, shutting down non-critical

Stock No. 80031
Stock No.
80030 80031

Stock No. 80030
Time Delay Value
0-60 minutes adjustable 5 minutes fixed

Stock No.
75525 75526 75527 75528

Description
Electronic Low Voltage Disconnect Electronic Timer for Interior Lighting Smart Battery Isolator Controller Electronic Voltage Sensing Relay & Timer

15 amps 20 amps

Call Toll Free 1-800-328-2724

email: sales @waytekwire.com

109

Cable Ties

Max Current

Fuses & Circuit Breakers

loads when the cutoff voltage is reached, or at the set time after the ignition is turned off • Timer and voltage sensor in one easy-to-connect unit 12V or 24V Application

Switches & Relays

- power switch turns off • If voltage drops <11.8 with the timer running - power switch turns off • Microprocessor controller and solid state output with over-current shutdown • Standard automotive relay pin format • Compact size with panel-mount bracket • Durable metal case

Electronic Low Voltage Disconnect

• Preserves battery charge and protects battery banks by automatically
Electronic Timer for Interior Lighting

• Unit prevents the internal lights inside from being left on and draining the
battery

• Vehicle operator operates a momentary switch, which turns lights on • After 20 minutes the FlexMod™ flashes the lights and gives the operator
warnings to either exit or reactivates the timer before the lights go out

Lights & Accessories

disconnecting loads when battery voltage drops to a critical level

Heat Shrink Products

• Small robust electronic modules that can be programmed to do almost any job • Ultra low 1mA standby current • Rated for more than 1,000,000 on-off cycles • Provides overvoltage and overcurrent protection to every direct load in that circuit • Small lightweight sealed design

Tapes & Chemicals

Protection Products

Sure Power Stock No.

Operating Voltage

Clamps & Clips

Wire Coverings

loads from batteries to prevent excessive discharge • Reconnects loads if vehicle is started or battery is recharged • Prevents loads from disconnecting during starting • Manual override to connect or disconnect during emergencies • Available in adjustable or preset models from 9 to 25 volts • Audible or visual alarm 1 minute before disconnect • Maximum load current up to 300A • Thermally protected • Low standby current

engine must be started to charge the battery or turn off lights, entertainment, communication equipment, etc., in use • Trip point prompts an audible alarm when the lights, flashers or any other appliance has depleted the battery voltage • When relay is open, the LED will flash; closed in normal operation, the LED will be off • 1 ⁄ 4" male tab contacts

the starting battery bank to ensure sufficient power for starting • Automatically reconnects loads if vehicle is started or battery is recharged • Start signal input override to prevent the loads from disconnecting during starting • Manual override for connecting or disconnecting during emergencies • Audible or visual alarm output activates 1 minute before disconnect • 1 ⁄ 4" male tab contacts, 1 ⁄ 4" studs

Tools

Terminals & Connectors

• Designed as a warning signal that the

• Disconnects predetermined loads from
Waytek Catalog 225

Table of Contents for the Digital Edition of Waytek Catalog 225
